ISO 17025 accredited

Gas Flowmeter Calibration

 

 

Request A Quote

gas flowmeter calibration iso 17025 accredited alliance calibration-2

Capabilities:

  • Gas Flow Speed-492 to 2,953 ft/min

  • Vane Anemometer Calibration

  • Hot Wire Anemometer Calibration

 

What is the difference between gas flowmeter calibration and mass flowmeter calibration?

 A gas flowmeter measures the amount of a substance that flows through the device and would be expressed some amount of volume in a given time e.g gallons/min.

Remember the ideal gas law:

pV=nRT

where

p= pressure

V= volume

n= number of moles

R= Universal gas constant

T= temperature in K

Volumetric measurements must compensate for pressure and temperature.

A Mass flowmeter actually measures the amount of mass that flows through the device. 

Mass is not dependent on temperature of pressure.

 

Mass Flowmeter Calibration

mass flowmeter calibration iso 17025 accredited alliance calibration-1

 

Anemometer Calibration

anemometer calibration iso 17025 accredited alliance calibration-2hot_wire_anemometer-calibration alliance calibration

Brands we calibrate:

  • Alicat
  • Rosemount
  • Kobold
  • Omega
  • TEC
  • Extech
  • Fluke
  • Hobo
  • CDI
  • Aalborg
  • TSI Alnor
  • Kanomax
  • LaCrosse
  • Cole-Parmer
  • Parker
  • Intek
  • Sesnirion
  • Hedland
  • Onset
  • Digi-Sense
  • UEI
  • Dwyer
  • Honeywell
  • Tektronix
  • Testo
  • Celestron
  • Cardone
  • Fieldpiece
  • and more.....

 

 

Frequently Asked Questions

Gage ID Number

Description and Size of Gage

Calibration Cycle

Check Points (if not specified, we adhere to our quality policy)

Gage ID is the unique identifier you use to identify the specific piece of equipment.

Calibration Cycle is the interval between calibrations.

 We use this information to provide a sticker for the calibrated instrument to show when it was calibrated and when you want it calibrated again.

 

 

 

 

YES!

Please include power cords, leads, and any accessories necessary for us to perform the calibration.

 

 

All ISO 17025 accredited calibrations are traceable through NIST or another NMI(National Metrology Institute) to the SI Unit. 

Calibration certificates include as-found data, as-left data, and measurement uncertainty.

Alliance Calibration

11402 Reading Road

Cincinnati, OH 45241

We do offer onsite calibration service within a 150-mile radius. Not all calibrations are best suited for onsite calibration.

Please contact Customer Service with your specific question.

The minimum order is $100.

No.

    Still, Have Questions?

        Request A Quote

        You Might Want To Read.......

        How to Use an IR Gun

        Measuring the temperature of something from a distance? Why yes, there is a tool for that. It's called an infrared gun — or an IR gun for short. An IR gun has a lot of potential applications. With an..

        January 10, 2022

        Why Torque Wrench Calibration is Important

        You'd be hard pressed to find a well-stocked toolbox that didn't have a torque wrench. This useful tool is a go-to for the DIY handyman and the professional machinist alike. They're constantly used..

        December 23, 2021

        Common Uses for Bore Gages

        A bore gage is a tool you use to measure a bore. No, not the kind that makes you feel tired and dull and like you want to leave a party. We’re talking about the kind that is synonymous with a hole...

        November 9, 2021

        What are Vernier Calipers?

        There are several types of calipers out in the world, and one of the handiest is the vernier caliper. This common tool is simple yet precise. It has a jaw-like structure at the end of a ruler...

        October 26, 2021